WellTech

WellGate 2608



Specification

  • Interface:
    • Ethernet port (RJ-45, 10/100 base-T)
    • 1-WAN port, connect to IP Network
    • 4-LAN port connect to PC with NAT
    • Support Bridge and NAT mode
    • Telephony port (RJ-11 x 8 pcs)
    • DC +12V power input Jack
    • Reset key to return Factory setting
    • LED Indicator for System, SIP and FXS status
  • IP Network connection
    • IPv4 (RFC 791)
    • Configurable WAN HTTP port, 80, 1024 to 65535
    • Configurable WAN HTTPS port, 443, 1024 to 65535
    • IP/ICMP/ARP/RARP/SNTP
    • Static IP
    • DHCP Client (RFC 2131), WAN port
    • DHCP Server, LAN port
    • Specify maximum DHCP Lease Time
    • NAT Server (RFC 1631)
    • PPPoE Client
    • DNS Client
    • Auto or Manual configure DNS Server IP address
    • Behind NAT, use DMZ for NAT traversal
    • Use STUN for NAT Type 1 and 2 for NAT Traversal
    • SNTP with time zone setting
    • TCP/UDP (RFC 793/768)
    • RTP/RTCP (RFC 1889/1890)
    • IPV4 ICMP (RFC 792),
    • TFTP Client
    • QoS : DiffServ (DSCP RFC 2475), ToS (RFC791, 1394)
    • Configure DSCP on RTP and SIP signal separately
    • Configure ToS on RTP and SIP signal separately
  • SIP Protocol :
    • RFC3261 compliance
    • Support local SIP and RTP port configure from 1 to 65535 at each line and SIP
      trunk.
    • SIP UDP Protocol
    • Support RFC 3325 to send “ anonymous “ or not at caller ID
    • SIP Session keep mode : Disable, Empty packet, SIP options, SIP register and
      SIP Ping ( Nortel ).
    • Support SIP HOLD Type
    • SIP Session Timer (RFC 4028)
    • MD5 Digest Authentication (RFC2069/RFC2617)
    • Reliability of provisional response PRACK (RFC3262)
    • Early/Delay Media support
    • Offer/Answer (RFC3265)
    • Message Waiting Indication (RFC3842)
    • Generate Ring Back tone or Custom Tone after received SIP message 100
      trying
    • Event Notification (RFC3265)
    • REFER (RFC3515)
    • Support Outbound Proxy
    • Support Primary and Backup SIP Server
    • Support STUN NAT Traversal
    • Support “rport” parameter (RFC 3581)
  • Audio Codec :
    • G.711 A-law/μ-law, G.729, G.723.1 (6.3K, 5.3K),G.726-32
    • Display IP Bandwidth with selected codec and payload
    • Select Voice Codec Order : Local or Remote
    • Silence Suppression
    • VAD/CNG selection
    • LEC : Line Echo Canceller
    • Packet Loss Compensation
    • Configure INPUT, OUTPUT and DTMF Gain
    • In-band/out of band DTMF (RFC4733, RFC2833 / SIP INFO)
    • Adaptive/Configurable Jitter Buffer range: 0 to 200ms
    • G.168 Acoustic Echo Cancellation
    • Dialing Plan with drop, replace, Insert dialing digits
    • Select First digit and Inter digit timeout duration (Sec)
    • Selectable Call Progress Tone
    • Support Specified Line Calling
  • Call Features :
    • Caller ID display DTMF (before 1st ring) and FSK (before 1st ring ), ETSI and
      Bellcore
    • DTMF Caller ID start and stop BIT (A,B,C,D,#) configurable
    • Polarity Reversal before Caller ID or not
    • Tone Generation: Ring Back, Dial, Busy, Call waiting, ROH and Disconnect
      tone
    • Configure Tone Frequency, Cadence, Level and Cycle
    • CDR output Server IP address and port number
    • SYSLOG output Server IP address and port number
    • NAT Traversal support STUN and IP Sharing
    • Payload type setting : RFC2833, FAX Bypass and Modem Bypass
    • Out-Band DTMF : RFC2833 and SIP Info
    • DTMF detection Sensitivity setting : 1 (Lowest signal level) to 5
    • DTMF generate configurable Duration and Interval Time
    • Ring time limitation : 10 to 600 seconds
    • Remote user drop call indication : Polarity Reversal or Loop Current Drop
    • Network Connection Detection
    • Network Unavailable announce Programmable Tone or Voice
    • Message Waiting Indication
    • Before dial first digit wait timeout configuration ( 1 to 60 sec )
    • Inter Digits Timeout configure : 1 to 5 seconds
    • Speed Dialing ( 50 sets )
    • Call Waiting/Switching between Calls
    • Call Forward (Busy, Unconditional, No Answer)
    • No answer forward time setting
    • Line service enable or disable
    • Sequential Ring or Simultaneously Ring to each line
    • Each line Ring Time setting at Sequential Ring
    • Display each Line registration status
    • Configure each line Ring priority at sequential ring
    • Block Anonymous Call
    • DND ( Do Not Disturb )
    • Call Hold
    • Configurable Call HOLD Tone or Music
    • Call Transfer
    • Flexible Dial Plan
    • Dial Plan: Dial out immediately when matched leading digit and total digits
      count ( 50 entries )
    • Digit Manipulation (Drop and Replace Rule) :
    • Apply Rule to FXS dialing out, IP incoming to FXS or pre-program 4 different
      groups
    • Insert pause key (p) by 2 sec at DM group only
    • Matched Prefix Code
    • Matched minimum digit length
    • Replace start and stop digit position
    • Replace number
    • Call Routes :
    • Support Peer to Peer (P2P) Call only
    • Matched Called Prefix code
    • Matched Minimum Called digit length
    • Secondary Backup Routes
    • Support additional Digit Manipulation Group rule
    • Hot Line
    • Outgoing SIP Caller ID Selection
    • Flexible Routing Plan
    • Prefix Match and Length
    • Priority Ring
    • Cyclic Ring
    • Simultaneous Ring
    • Programmable Hunting Cycle
    • Backup Routing with Digit Manipulation
    • Default Routing
    • FAX Transmission mode : T.38, Bypass or Auto
    • FAX Bypass Keyword required from SIP Server
    • FAX Bypass Codec : G.711 u-Law or G.711A-Law
    • Support Peer to Peer Dialing
    • Flash Time Detection: range from 60 to 2000 ms
    • Flash Key definition: Disable, Transfer or SIP Message
    • ON-HOOK Voltage -48Vdc
    • Configure Ring Cadence, Frequency and Voltage
    • Distinctive Ring Pattern by incoming Caller ID digit length
    • Provide world wide country telephone line Impedance
    • Ring Frequency range setup : 15 to 100 HZ
    • Ring ON duration : 100 to 8000 ms
    • Ring OFF duration : 100 to 8000 ms
    • Ring AC RMS Level Voltage : 0 to 94 Vrms
    • Support Polarity reversal for Billing
    • Service Up to 1 Kilo-meter distance to analog telephone set
    • Generate Current Drop Time (Open Loop Disconnect time)
  • MANAGEMENT :
    • Administrative Telnet, HTTP, HTTPS
    • WAN IP address voice announcement from analog phone by dialing #126#
    • LAN IP address voice announcement from analog phone by dialing #120#
    • HTTP/FTP provision through MAC address
    • 3 Levels of User Access Right with Password protection (Administrator,
      Supervisor and User)
    • HTTP/HTTPS Service Access limitation from WAN port
    • Provides System Status Logs
    • Status display: Network, Line, SIP Trunk status
    • Diagnostics (debug through Syslog Event Notice)
    • Debug in real time by Telnet
    • Configuration Backup/Restore
    • Upload user recorded voice announced file: Greeting, Hold Music, and Network
      Failure
    • Dual Firmware Image Backup
    • Reset to factory Default

    ** Support Welltech proprietary encryption protocol at SIP Signal and Voice codec
    during transmitting to IP network in order to Anti-ISP block of VoIP call. This
    feature only be available with Welltech SIP server or SIPPBX6200 IP-PBX

  • Environmental :
    • Actual Dimension: 24(W) × 3.4(H) × 16(D) CM
    • Weight: 1.5kg (One unit with packing)
    • Operating Temp. & Humidity
      • Temp.: 0°C~45°C (32°F~113°F)
      • Humidity: 10%~90% relative humidity, non-condensing
    • Power Adaptor:
      • INPUT: AC100V~240V, 50/60Hz
      • OUTPUT: DC 12V, 3.0A
  • Approvals:
    • CE, FCC (Part 15, Class B), LVD and RoHS
  • Country of origin:
    • Made in Taiwan
  • Packing Accessories
    • WellGate 2608 x 1 pcs
    • AC to DC+12V Power adaptor x 1 pcs
    • CD User Manual x 1 pcs
  • Warranty
    • One year